QA/QC Inspector I

ACCO Engineered Systems•Colorado Springs, CO

About The Position

The QA/QC Inspector I performs visual inspection and verification of materials, equipment, piping systems, welding, and brazing installation work on assigned projects and in fabrication shops, recording results as objective evidence. The position works to project specifications, applicable ASME piping codes, manufacturer requirements, customer site requirements, and ACCO’s welding program. This is the entry inspection level, below Inspector II and Inspector III. The Inspector I performs inspections within their scope and creates complete, retrievable records, following an inspection plan established by the QA/QC Area Supervisor or assigned Inspector III. Technical direction comes from an assigned Inspector II or III, or, if neither is assigned, the next QA/QC manager in line. Day-to-day site coordination is provided by local project leadership, while inspection decisions and quality records follow the QA/QC reporting line. The role supports fabrication, installation, and project management teams, raises findings for resolution, and seeks to inspect work before it is covered. The position’s inspection activities include receiving, in-process, and final visual inspections of piping and mechanical systems, as well as participation in scheduled hold and witness points, pressure tests, system walkdowns, punch-list inspections, and pre-turnover verification. The Inspector I documents inspections and nonconforming conditions, communicates findings to project and QA/QC leadership, and may hold specific work from proceeding until its inspection is performed. The position does not qualify welders or brazers, approve welding procedures, serve as the Certified Welding Inspector of record, approve repairs or deviations, issue or disposition nonconformance reports, or sign turnover documentation or final quality letters. This is a non-exempt role with hours and shift schedules determined by area project requirements and applicable law. Overtime, shift work, and weekend coverage occur based on project schedules and are compensated under company policy and applicable law. Travel to offices, fabrication facilities, and project sites is based on business needs; work location varies by assignment, and overnight travel may be required. The role has no direct reports and involves work at active construction sites and fabrication shops, including elevated work areas and confined spaces, using required fall protection and personal protective equipment. The listed wage range is $29.98 to $38.79 per hour; actual compensation depends on candidate- and location-specific factors.

Requirements

  • Three or more years of experience in construction or fabrication quality control.
  • One to two years of experience on semiconductor, high-purity, cleanroom, data center, or comparable technically demanding projects involving work such as cleanroom piping, process utilities, tool hook-ups, or chemical and gas systems.
  • Current ASNT or ACCP VT Level I or Level II certification, at the level required by assigned duties and project requirements, meeting the ACCO Standard Written Practice and examination requirements, and approved by the ACCO ASNT Level III.
  • Annual Jaeger J1 near-vision examination.
  • Ability to read and interpret isometrics, P&IDs, shop drawings, specifications, and inspection reports.
  • Working knowledge of weld and braze visual acceptance criteria, mechanical piping systems, and high-purity cleanliness and workmanship standards.
  • Ability to write clear, factual inspection reports.
  • Regular and routine attendance.
  • Valid driver’s license and reliable transportation to assigned project sites.
  • Ability to meet the stated physical demands, with reasonable accommodations as applicable, and to use required fall protection and personal protective equipment at active construction sites and fabrication shops.

Nice To Haves

  • Familiarity with PT, MT, UT, and RT sufficient to read a third-party examination report and understand what was examined, the applicable criteria, and the result; certification to perform these methods is not required.
  • OSHA 10 or OSHA 30 training.
  • Confined-space training.
  • First aid and CPR training.
  • Experience with Box, Bluebeam, Smartsheet, Procore, or PlanGrid.
  • Conversational Spanish.

Responsibilities

  • Perform visual examinations of welded, brazed, soldered, and mechanical joints, including grooved couplings, press fittings, flanges, and threaded connections.
  • Inspect pipe fit-up, alignment, joint preparation, cleanliness, support and hanger installation, and general workmanship.
  • Inspect received materials and equipment against submittals, packing lists, and required documentation.
  • Perform in-process and final visual inspections of high-purity process piping, clean utilities, chemical and gas systems, hydronic systems, and HVAC mechanical systems.
  • Attend scheduled hold and witness points and participate in pressure tests, system walkdowns, punch-list inspections, and pre-turnover verification.
  • Verify compliance with project specifications, customer site requirements, applicable ASME and AWS codes, manufacturer requirements, and ACCO procedures.
  • Verify that welding procedure specifications are approved and applicable and that welder qualifications and continuity are current for the process in use.
  • Verify material traceability, including heat numbers, material test reports, and lot identification, and check that measuring and test equipment is within its calibration period.
  • Submit a daily inspection report with photographs for every project day worked, filing it to the project QA/QC folder the same day.
  • Complete inspection records, weld maps, fit-up logs, brazing logs, torque logs, and visual inspection records legibly and contemporaneously.
  • Document nonconforming conditions with sufficient description, location, and photographic evidence for someone not present to understand the finding.
  • Maintain personal certification and training records and respond to expiry notifications.
  • Communicate findings clearly and professionally to the Foreperson, Superintendent, and QA/QC leadership; support assigned Inspector II and Inspector III personnel and accept their work direction.
  • Participate in ACCO safety programs and demonstrate commitment to a goal of zero injuries or incidents.
  • Identify and document nonconforming material, workmanship, or documentation and bring it to the assigned Inspector III.
  • Place a hold on the specific work being inspected and require that it not proceed past an inspection point until the inspection is performed.
  • Reject received material that does not match the submittal, specification, or required documentation.
  • Stop and immediately notify the Inspector III and Project Manager if work in progress presents an immediate quality or safety risk.
  • Perform other duties assigned by QA/QC leadership in conjunction with the project team.

Benefits

  • Potential $2,000 sign-on bonus for Inspector I, paid after six months of employment and void if role expectations are not met.
  • Annual pay-rate reviews and increases.
  • Discretionary performance bonuses following regular performance evaluations.
  • Relocation packages for qualified roles.
  • Competitive per diem allowances for project-based roles to support housing needs.
© 2026 Teal Labs, Inc
Privacy PolicyTerms of Service