Continuous Opr - A Shift - 7:30am - 7:45pm (4on - 4off)

NGK Ceramics USA, Inc.•Mooresville, NC

10h•Onsite

About The Position

Operates, monitors, and assists in the drying and finishing processes, which involve the drying; the automated cutting; the visual inspecting; and the manual stacking of dried, formed products. These products are supplied to the kiln area where they are fired in kilns, producing ceramic products that meet required specifications and quality standards.

Requirements

Must be on your current job for one (1) year if your job grade is 7 or lower.
No disciplinary actions within the last year (low level points warnings may be waived if there are special circumstances that can be, or are, documented).
Meet the minimum requirements of the open job description.
Completion of the current learner’s assessment and other training requirements.
Completed Career Readiness Certificate (CRC).
Must be able to successfully complete all required job training.
High school diploma or general education degree (GED).
6 month manufacturing/warehousing experience or equivalent
CRC Bronze or above
Ability to read and comprehend work instructions.
Ability to communicate information in one-on-one and small group situations to other employees of the organization.
Ability to add and subtract, multiply and divide in all units of measure, using whole numbers, common fractions, and decimals.
Ability to apply common sense understanding to carry out instructions furnished in written, oral, or diagram form.
Ability to deal with problems involving a few concrete variables in standardized situations.

Nice To Haves

Basic knowledge of Statistical Process Control (SPC) software.
Certified Production Technician program completion

Responsibilities

Performs established start-up procedures in accordance with work instructions.
Verifies that the finishing machine set-up, as well as the production line set-up, have been successfully completed once automatic processing has begun.
Inspects greenbody wooden pallet for damage; confirms that both sides of the wooden pallet have the same pallet number; and places finishing pallet cart on table lift in a safe and efficient manner.
Calculates and verifies the number of layers and pieces of greenbody per layer for each travel ticket quantity.
Picks up the product that is deposited onto the finishing table by the third transfer; applies part specific visual criteria understanding to visually inspect the entirety of each part; and places the approved parts onto the pallet in the proper manner.
Places white cardboard between each layer of greenbody, using the proper technique; when proper amount of product has been placed on finishing pallet, lowers cart and rolls cart to a location where the pallet may be easily removed by the forklift; and places the Finishing Travel Ticket on the finished pallet.
Enters complete and accurate process information into the company’s information systems.
Determines maximum allowable values for dimensional characteristics (perpendicularity and length) by referencing the Target Sheet; checks length and perpendicularity; and determines location and magnitude of maximum perpendicularity variance by using the proper test timing.
Calculates accepted, rejected and handled part quantities; performs yield/defect rate calculations; and calculates the number of total cuts on a specific blade and/or sets of blades and records the required information.
Segregates and stacks/disposes of shiro-modori; wraps pallet and completely and accurately fills out the modori tag.
Performs re-inspection tasks, including completely & accurately filling out the Re-Inspection Form.
Completes the Drying/Finishing Activities Log to document the amount of time not processing parts; performs equipment setting adjustments and troubleshoots process and equipment problems; performs established change-over procedures, as required.
Starts dryer operations according to established power up procedures; verifies initial settings for: exhaust fan, heater temperature, supply fan, etc.
Calculates relay evaporation ratio when product forming begins.
Checks continuous dryer conditions twice per shift & records on the Continuous Dryer Condition Check Sheet; performs carrier change outs as needed, according to product being produced.
Adjusts machine settings to facilitate the manufacture of quality dried formed products.
Works safely by avoiding forklifts; staying clear of forklift doors; and using personnel doors when entering or exiting the buildings.
Participates in PM (Preventive Maintenance), MMOL (Machine Maintenance Operator Leader), and G5S (Global 5S: Sort, Set in Order, Shine, Standardize, Sustain) activities as needed.
Follows all EMS (Environmental Management System) procedures, including the disposal of waste and used materials.