Sheet Metal Mechanic

Brady Services • Greenville, NC

18h • Onsite

About The Position

The Sheet Metal Mechanic supports Contracting Operations by performing sheet metal installation. Responsible for assisting the team in other areas if sheet metal work is not available.

Requirements

• High school diploma or general education degree (GED)
• Three to five years related experience and/or training
• Proficiency with computer devices (including laptops, tablets and smart phones) and working knowledge of Microsoft Office, Adobe Acrobat, and Apple iOS software.
• Ability to pass drug screening.
• Ability to prove US employment eligibility.
• Must possess a valid driver’s license.
• Regularly required to stand, walk, bend, stoop, crouch, kneel, squat, balance, and climb, with occasional sitting and lying.
• Requires working in confined/constricted spaces and at elevated heights (e.g., ladders, scaffolding, rooftops).
• Material handling demands include lifting from floor level to overhead and maneuvering in tight or awkward spaces.
• Ability to lift and carry or otherwise move: Up to 25 pounds constantly, Up to 50 pounds occasionally, Over 50 pounds only with mechanical assistance or team lift, following safety protocols
• Associates are expected to lift no more than 50 pounds independently, unless assisted by appropriate equipment or a team lift.
• Team lifts are required for any load exceeding 50 pounds per individual, with clear communication protocols, including verbal confirmation and coordinated movements, to ensure safety.
• Must always follow proper lifting techniques and safety protocols.
• Frequent use of hands and wrists for repetitive tasks such as tool use, wiring, or securing fasteners.
• Must have sufficient hand-eye coordination and manual dexterity to use hand tools, power tools, and electronic diagnostic equipment.
• Must be able to work at heights.
• Must be able to climb and perform tasks while positioned on ladders.
• Regularly required to use hands to operate objects, tools, or controls, and reach with hands and arms.
• Must be able to communicate effectively and perceive verbal instructions and warnings in a high-noise industrial environment (above 85 dBA), while wearing required hearing protection.
• Vision abilities required include close vision, distance vision, color vision, peripheral vision, depth perception, and the ability to adjust focus.
• Must have the physical capacity to work extended hours, including overtime and weekends, during peak demand or emergency service periods.
• Must wear appropriate PPE, including but not limited to: safety glasses, safety-toed boots, hard hats, high-visibility vests or shirts, task-specific gloves, and hearing protection, as required by the work environment.
• Hard hats are required when working in areas with potential overhead hazards.
• All PPE must comply with OSHA standards and be inspected daily for proper condition, fits appropriately, and is free of defects.

Nice To Haves

• Two years of related trade school, preferred
• Refrigeration training or certification, preferred
• Specialized PPE (e.g., respirators, arc-rated clothing, fall protection) may be required depending on task-specific hazards, and training will be provided as needed.

Responsibilities

• Install sheet metal products, such as ductwork and ventilation systems, ensuring proper fit and alignment
• Plan, layout, and fabricate Ductwork parts, components, and assemblies
• Proficiency in sheet metal fabrication techniques, soldering of water lines, brazing of refrigeration lines
• Must be familiar with various HVAC equipment such as air handlers, package units, condensers, coils, exhaust fans, etc.
• Install gas lines and refrigeration lines as needed
• Provide sheet metal instruction and assist in the training of the sheet metal assistants
• Must be able to read and understand blueprints, technical drawings, and specifications.
• Measuring, marking, cutting, bending, and shaping sheet metal according to blueprints and specifications.
• Attend training to be updated on industry practices as needed
• Experienced in the use of a variety of power and hand tools such as drills, saws, hammers, shears, seamers, etc.
• Able to climb ladders, work on roofs, and work from a variety of aerial work platforms
• Demonstrate familiarity with HVAC system components such as supply and return, liquid and suctions lines, and exhaust ventilation
• Assist in rigging and setting of HVAC equipment
• Work with direction from on-site installation foreman
• Must be able to work at heights from a ladder or aerial work platform
• Follow all safety regulations and wear appropriate personal protective equipment (PPE).
• Assists other team members with job duties as necessary
• Ability to travel to the customer’s locations
• Ability to work weekends and/or evenings as necessary

What This Job Offers

• Job Type: Full-time
• Career Level: Mid Level
• Education Level: High school or GED