Maintenance Technician
Eaton Corporation•Camarillo, CA
•Onsite
About The Position
Eaton’s IS AER ITD division is currently seeking a Maintenance Technician at our Camarillo facility! The core hours are 6:00am to 2:30pm Monday - Friday. Overtime may extend these hours. The hourly rate for this position is $23.00 per hour. Please note the salary information shown above is a general guideline only. Salaries are based upon candidate skills, experience, and qualifications, as well as market and business considerations.
Requirements
- Must have a High School Diploma or GED from an accredited institution
- A minimum of 2 years hands-on experience in industrial maintenance (mechanical, hydraulic, or electrical)
- Only candidates residing within the immediate area of Camarillo, CA (50 miles) will be considered for this position.
- This position requires access to export-controlled information. To conform to U.S. Government export regulations applicable to that information, applicant must be a U.S. person, defined as a (i) U.S. citizen or national, (ii) U.S. lawful, permanent resident (green card holder), (iii) refugee under 8 U.S.C. 1157, or (iv) asylee under 8 U.S.C. 1158.
- Strong troubleshooting skills and mechanical aptitude
- Ability to work independently and manage priorities
- Good mechanical aptitude with knowledge of practices, tools and equipment used in mechanic’s trade
- Knowledge of procedures for installing all sizes of electrical conduit, cables, wires, switches, automatic stating equipment, and pole line construction, etc.
- Hands-on experience troubleshooting and repairing machine shop equipment including Haas CNC Lathes, Mazak CNC Lathes, Haas Mills, Moroski Mills, Injection Molding Machines, Thermal Transfer Molding Machines, and Reciprocating Stamping Presses
- Hands-on experience troubleshooting and repairing facility equipment including chillers, cooling towers, thermolators, air compressors, and water treatment systems
- Troubleshooting and repairing hydraulic pumps, valves, cylinders, manifolds, and accumulators
- Industrial control systems, limit switches, safety circuits, relays, contactors, and motor starters
- Ability to troubleshoot control issues using schematics, multimeters, and diagnostic tools
- Must be able to work under minimum supervision and be self-motivated
- Must be willing to work outdoors in both hot and cold weather
- Ability to operate industrial equipment including forklifts, scissor lifts, and boom lifts
- Ability to push, pull and lift up to 50 lbs
Nice To Haves
- Experience with 480V 3‑phase systems, motor controls, and VFDs
- Familiarity with power distribution systems up to 600V
- Experience with emergency power or process control systems
- Experience in performing power system analysis, short circuit and load flow studies. Familiarity with process control systems and emergency power systems is a plus
- Knowledge of municipal electrical code applicable to installation, maintenance, and repair work
- Hands‑on experience troubleshooting Variable Frequency Drives (VFDs), including parameter setup, fault diagnostics, and motor performance issues
- Working knowledge of PLC systems (Allen‑Bradley, Siemens, or similar), including Basic ladder logic interpretation, I/O troubleshooting, Sensor, switch, and interlock diagnostics
- Trade or technical school certificate or equivalent preferred
Responsibilities
- Support and comply with Eaton Environmental, Health, and Safety (EHS) policies
- Troubleshoot, diagnose, and repair electrical, mechanical, and hydraulic systems with little to no supervision
- Conduct preventive maintenance (PMs) and planned shutdown work to improve equipment reliability
- Perform a variety of maintenance/minor repair activities but not limited to painting, drywall, parking lots, plumbing repairs, lighting, flooring, and roof.
- Perform basic electrical work (120V) and support higher‑voltage systems as qualified
- Operates maintenance work order system to complete assignments and provide feedback
- Read and understand electrical, mechanical, and hydraulic schematics.
- Assist with motor control, starters, and basic troubleshooting of electrical components
- Perform welding and metal repair to restore or improve equipment
Benefits
- Health and Welfare benefits
- Retirement benefits
- Programs that provide for paid and unpaid time away from work
Stand Out From the Crowd
Upload your resume and get instant feedback on how well it matches this job.
Upload and Match Resume
What This Job Offers
Job Type
Full-time
Career Level
Mid Level
Education Level
High school or GED
