Maintenance Tech Level 3/4

PCC Talent Acquisition Portal•Gardena, CA

20h

About The Position

Level Three: Level three mechanics work under minimal supervision to perform turret/spindle alignments, PM tasks such as trouble shoot lubrication system, hydraulics, bar feeders, etc. trouble shoot controls, issues etc., able to diagnose and repair most any NC mechanical issues; pull and replace ball screws, hydraulic and pneumatic issues. Able to complete any task given related to facility maintenance demonstrating expertise in plumbing and general carpentry and numerous tasks involved in facility related issues. Demonstrating the ability to read mechanical drawings and electrical schematics, while serving as either a mechanical or technical SME. Typically, 6-10 years of experience. Primary Duties & Responsibilities: Work safely under functional safety guidelines such as PPE and equipment interaction. Mechanical-Able to diagnose and repair most any CNC mechanical issues such as turret and spindle alignments, pull and replace ball screws, hydraulic & Pneumatic issues, and most any mechanical issues. Electrical: Able to read and understand electrical drawings ladder logic/relay logic and use in troubleshooting. Perform Preventive Maintenance according to schedule. Able to identify electrical components such as relays, micro switches and proximity sensors. Able to read and understand electronic drawings and use this information and troubleshoot various types of machines such as CNC lathes and mills, induction heaters and laser markers. Troubleshoot and diagnose any NC control or servo drive issues. Interface with manufacturers online tech support when needed. Check functionality of machines worked after repair, maintenance and installation. Assist Maintenance Level 4 for spindle stator rebuild axis linear guides and ball screws. Perform carpentry work on permanent structures, office partition, panels, floors, office. Perform facility worked, roof, electrical, waste area, ac/heater issues. Plan and sequence of work operations to rebuild and functionality check all types of precision-built power machines tools (NC, lathes etc.) Plan, layout and fabricate replacement parts for major rebuilding of precision-built machine tools were set up and operation of basic machine tools to exacting tolerances is required. Fit and scrape bearings, fit and align spindles, columns, knees, tailstocks, ways and tables individually and in relation to each other. Perform good housekeeping practices. Perform other duties as required by supervisor or manager.

Requirements

Ability to read and write English
High-level competence in shop math such as working with fractions and decimals
High-level knowledge of hand tools and mechanical application regarding nuts and bolts
High-level knowledge of part holding methods and procedures
High-level knowledge NC equipment and controls
Ability to interact with computers and CNC controls at a high level
Ability to interact and troubleshoot hydraulic and pneumatic systems at high level
Ability to read electrical and machine drawings and diagrams at high level
Ability to perform complex Preventive Maintenance for all NC, lathes, etc. following equipment checklists and run a PM report with ball bar diagram
Ability to lead and instruct low level maintenance
High level experience working with mechanical processes and methods such as hand tools, and light equipment such as saws, drills and pneumatic tools

Nice To Haves

CNC maintenance training and certification

Responsibilities

Perform turret/spindle alignments
Perform PM tasks such as trouble shoot lubrication system, hydraulics, bar feeders, etc.
Troubleshoot controls, issues etc.
Diagnose and repair most any NC mechanical issues
Pull and replace ball screws
Address hydraulic and pneumatic issues
Complete tasks related to facility maintenance
Demonstrate expertise in plumbing and general carpentry
Read mechanical drawings and electrical schematics
Serve as a mechanical or technical SME
Diagnose and repair most any CNC mechanical issues such as turret and spindle alignments, pull and replace ball screws, hydraulic & Pneumatic issues, and most any mechanical issues
Read and understand electrical drawings ladder logic/relay logic and use in troubleshooting
Perform Preventive Maintenance according to schedule
Identify electrical components such as relays, micro switches and proximity sensors
Read and understand electronic drawings and use this information and troubleshoot various types of machines such as CNC lathes and mills, induction heaters and laser markers
Troubleshoot and diagnose any NC control or servo drive issues
Interface with manufacturers online tech support when needed
Check functionality of machines worked after repair, maintenance and installation
Assist Maintenance Level 4 for spindle stator rebuild axis linear guides and ball screws
Perform carpentry work on permanent structures, office partition, panels, floors, office
Perform facility work, roof, electrical, waste area, ac/heater issues
Plan and sequence of work operations to rebuild and functionality check all types of precision-built power machines tools (NC, lathes etc.)
Plan, layout and fabricate replacement parts for major rebuilding of precision-built machine tools
Fit and scrape bearings, fit and align spindles, columns, knees, tailstocks, ways and tables individually and in relation to each other
Perform good housekeeping practices
Perform other duties as required by supervisor or manager