Cabinet Builder II (Contract)

Greenpoint Technologies•San Antonio, TX

7d•Onsite

About The Position

Builds high-end aircraft cabinetry using a variety of veneers, laminates and composite materials in a timely and efficient fashion ensuring quality standards are attained. This is a temporary position employed through an agency.

Requirements

Minimum of high school diploma or equivalent.
Minimum of two years aircraft cabinetry experience.
US Citizen Required - this position is located at a facility that requires special access.
Ability to communicate in English (read, write and verbally communicate).
Mathematical knowledge and ability to apply towards problem solving.
Ability to identify and operate proper tools for the task assigned.
Exhibits hand-eye coordination skills.
Identifies application characteristics of adhesives and epoxies.
Ability to read measuring instruments.
Ability to correctly label parts for re-assemble.
Ability to build shop aids.
Ability to fabricate small sheet metal parts (angles, clips, brackets, etc.).
Ability to manufacture items needed for final assembly adjustments (shims, blocks, etc.).
Ability to travel as required.
Ability to work outside of core business hours as required.
Able to comply with DOT/FAA Drug and Alcohol Testing Program.
Able to climb and work on step stools and/or ladders.
Able to lift 25 lbs. without assistance/able to lift up to 100 lbs. with assistance.
Able to reach overhead.
Able to work in a non-dust-free environment.
Normal or corrected vision (required to perform exacting tasks).
Full range of motion with both hands.
Can work in a stooping, kneeling, standing position and in cramped areas.
Minimum Requirements Tool Box, Small Hammer, Awl, Calculator, Chisel Set (1/8" to 1"), Pliers (regular & needle nose), Putty knife, Scale (24 inch flex in 16R grads.), Scale (6 inch in 16R grads.), Screwdriver (Straight), Screwdriver (Phillips #1 & # 2), Square (12" Combo in 16R grads), Tape Measure (10') Dec/Frac, Utility Knife, Crescent Wrench (Sm &/or Med), Allen Wrenches (Sm Set), Wire Cutters, Offset Screwdriver (90 Degree), Tap Set, Calipers, Punch, Center, Vise Grips (sm), Flashlight.
Additional Tool Requirements: Socket Set, 90 Degree Die Grinder, Semco Sealant Gun, Trim Router, Angle Drill Motor, Large Hand Router.
An employee professing knowledge necessary to operate any machine on this checklist will be required to demonstrate these abilities. No employee should operate equipment until another employee who has proven experience on the equipment in question has instructed the employee in the set up and operation. The employee will be required to demonstrate the safe set-up and operation of the following items: Spray Gun (Contact Glue), Hand Tools (Small Electric and Pneumatic), Sander, Pneumatic or Electric (Hand Held), Router, (Hand Router, Table Router), Planer/Jointer, Press, Drill, Sander, (Disc, Spindle), Saw, (Band Saw), Saw, (Table Saw, Sliding Table Saw, Panel Saw), Surface Sander, (Drum Sander), Chop Saw.

Nice To Haves

Angle Drill suggested but not required.

Responsibilities

Reads customer specification documents.
Reads and interprets engineering drawings.
Works with aerospace materials consistently.
Prepares kerf and fiberglass panels.
Builds drawers and cabinets on medium monuments.
Applies and works with veneer on products.
Lays out and routes for switches, cup holders and inlays.
Installs inlays.
Lays out and cuts materials on the table saw.
Labels parts for re-assemble.
Builds shop aids.
Fabricates small sheet metal parts (angles, clips, brackets, etc.).
Manufactures items needed for final assembly adjustments (shims, blocks, etc.).
Bonds hinge blocks into panels, set doors, drawers, etc.
Wears safety equipment as required and complies with safety guidelines and procedures.
Produces a quality product consistently.
Properly maintains shop tools and equipment.
Maintains a neat, organized work area and help with the general daily housekeeping of the department.
Meets target hours and completes schedules as set by Supervision.
Maintains regular attendance including being at work, being on time to work and working full shifts.
Other duties as assigned.