Auto Punch Press Operator-3

ABB•Saint Louis, MO

1d•$23 - $29•Onsite

About The Position

ABB helps industries run leaner and cleaner, and every person here makes that happen. This position reports to the Production Supervisor and is responsible for operating an auto punch press, specifically in the lamination process. Operators will be trained in all steps of the job, including safety procedures, equipment operation, and quality checks. The role requires the ability to perform essential functions for a minimum of 8 hours per day, 5 days a week, with the possibility of daily and weekend overtime on short notice. ABB is committed to providing reasonable accommodations for employees unable to perform essential functions due to disability.

Requirements

Ability to perform essential functions for a minimum of 8 hours per day, 5 days a week.
Follow Work Instructions Manual lifting requirements up to 50 pounds.
Operator will be trained on all steps of the job.
Operator will be trained on operating electric pallet truck.
Must know where Emergency Stops are located for the press you are running.
Must check Emergency Stops and light curtains to be working properly.
Verify the Press Release Form (QFSL-A001) is located at the press and is signed by a supervisor before running the press.
Visually inspect parts for burrs, chips, slug marks, bent teeth and missing features.
Flatness must be checked 3 times per coil.
Must verify inventory tags, coil #’s and blueprints match the work order.
Match the part to the blueprint.
Trained on how to feed the material through the straightener, feeder and up to the starting point in the die and slowly inch the material through the die.
Always ensure the strip is receiving plenty of lubrication.
Must keep an eye on the loop between the presses and scrap conveyor to be running.
The operator will use an air wire twister to wire the stacks of lamination.
At the end of the die run the operator will turn off the press, dereeler, straightener and the feeder.
Must fill out a Red Tag for all Non Con material and move it to the Non Con area.
Once the flywheel has stopped the operator will remove the end coil strip out of the die and save it to be sent to Tool Room with the die, then wipe all the oil off of the die and clean area thoroughly.
Must work safely and pay attention to your surroundings and immediately report injuries, accidents and near misses to Supervisor.
Ability to understand and follow all ABB safety policies, safety training and hazard communication information.
Ability to lift and or carry up to 50 pounds.
Ability to frequently grip with hands, turn, push, and bend, along with occasional reaching above shoulder level, and pulling.
Ability to walk and/or stand for long periods of time and to keep up with the demanding pace of production.
Possess the dexterity and hand-eye coordination to utilize various hand tools, power tools, and other equipment to complete a variety of complex task.
Ability to assist in performing press-line equipment set-up and clearing of die jams.
Ability to comprehend and follow both written and verbal instructions.
Ability to read, write, use a calculator.
Must also have the ability to read and comprehend work orders, blueprints, inventory tags, and shipping labels.
Ability to maintain regular work attendance, including arriving at work on time and remaining at work until the end of the schedules work day.
Ability to work daily and weekend overtime, including overtime on short notice.

Nice To Haves

Stretching exercises will be done at the beginning of every shift.
Supervisor will go over Job Safety Analysis sheets, safety checklist, personal protective equipment (PPE) and instructions on performing daily clean up.

Responsibilities

Perform essential functions of an Auto Press Operator Lamination for a minimum of 8 hours per day, 5 days a week.
Follow Work Instructions Manual lifting requirements up to 50 pounds.
Operate electric pallet truck.
Ensure Emergency Stops and light curtains are working properly.
Verify the Press Release Form (QFSL-A001) is signed by a supervisor before running the press for each order.
Visually inspect parts for burrs, chips, slug marks, bent teeth, and missing features.
Check flatness 3 times per coil (back to back flatness check).
Verify inventory tags, coil #’s, and blueprints match the work order.
Match the part to the blueprint.
Feed material through the straightener, feeder, and up to the starting point in the die, slowly inching the material through the die.
Ensure the strip is receiving plenty of lubrication.
Monitor the loop between the presses and scrap conveyor.
Use an air wire twister to wire stacks of lamination.
Turn off the press, dereeler, straightener, and feeder at the end of the die run.
Fill out a Red Tag for all Non-Conforming material and move it to the Non-Con area.
Remove the end coil strip from the die after the flywheel has stopped and save it to be sent to the Tool Room with the die.
Wipe all oil off the die and clean the area thoroughly.
Work safely and pay attention to surroundings.
Immediately report injuries, accidents, and near misses to the Supervisor.
Understand and follow all ABB safety policies, safety training, and hazard communication information.
Wear proper personal protective equipment (PPE) such as safety glasses, hearing protection, safety shoes, cut resistant gloves, and safety sleeves when required.
Lift and/or carry up to 50 pounds.
Frequently grip with hands, turn, push, and bend, along with occasional reaching above shoulder level, and pulling.
Walk and/or stand for long periods of time and maintain the pace of production.
Utilize various hand tools, power tools, and other equipment to complete a variety of complex tasks.
Assist in performing press-line equipment set-up and clearing of die jams.
Comprehend and follow both written and verbal instructions.
Read, write, and use a calculator.
Read and comprehend work orders, blueprints, inventory tags, and shipping labels.
Maintain regular work attendance, including arriving at work on time and remaining at work until the end of the scheduled work day.
Work daily and weekend overtime, including overtime on short notice.

Benefits

Choice between two medical plan options: A PPO plan called the Copay Plan OR a High Deductible Health Plan (with a Health Savings Account) called the High Deductible Plan.
Choice between two dental plan options: Core and Core Plus
Vision benefit
Company paid life insurance (2X base pay)
Company paid AD&D (1X base pay)
Voluntary life and AD&D – 100% employee paid up to maximums
Short Term Disability – up to 26 weeks – Company paid
Long Term Disability – 60% of pay – Company paid. Ability to “buy-up” to 66 2/3% of pay.
Supplemental benefits – 100% employee paid (Accident insurance, hospital indemnity, critical illness, pet insurance)
Parental Leave – up to 6 weeks
Employee Assistance Program
Health Advocate support resources for mental/behavioral health, general health navigation and virtual health, and infertility/adoption
Employee discount program
401k Savings Plan with Company Contributions
Employee Stock Acquisition Plan (ESAP)
11 paid holidays.