Aerosol Production

QuestSpecialty•Brenham, TX

75d•Onsite

About The Position

The Aerosol Line Worker is responsible for maintaining the flow of cans to completion on the aerosol production line. Position on the production line can vary to include the following: can stager, water bath monitor, tipper, capper, and packer.

Requirements

Verify line stager has brought the correct cans to the line, using pallet tags on can pallets and batch ticket. Initial batch ticket once cans have been verified.
Inspect cans as they are loaded onto the table for the following: Rust, water, dirt, etc., inside the container that could cause contamination or corrosion; Rust on the exterior of the can; Dented cans; Imperfections in screened cans – scratches or dents.
All empty cans found to be defective need to be placed in a scrap box on the line and counted and documented on the batch ticket at the end of the run.
Cover any partial pallets with shrink wrap to keep cans from being exposed to the environment and to prevent cans from falling during transport.
Verify filled can weights for both production lines as cans are coming out of the gassing house.
Monitor screened cans for any signs of dents or scratches to the can due to the production line.
Monitor filled cans as they travel through the water bath for any signs of leaking cans.
Pull defective cans from the line or water bath as needed.
If cans are to be reworked back into the line, notify the machine operator.
For filled cans that are going to the waste area, label the box with the product number so that the cans can be discarded to the appropriate waste stream. Do not throw any filled cans into the trash can.
Notify the machine operator to stop the line if any items listed above are found.
Verify correct tips have been brought over to the line by comparing the label on the box of tips to the item number listed on the batch ticket. Initial batch ticket once tips have been verified.
Make sure enough tips have been pulled to the line, so as not to hamper production efficiency.
Prior to line startup, ensure the correct lot code has been entered in the can inkjet printer. Test a few cans to ensure the lot code is clear and legible once printed on the can.
Set up the label machine and ensure labels will go onto cans correctly.
Keep visual checks on cans, looking for any damaged or leaking cans.
Make timely checks that the lot code is being printed onto cans. Stop line if lot numbers are not printed on cans.
If any labels are wrinkled or crooked, remove from the line to be reworked.
Upon completion of an order, close and tape the box of tips and place a “PARTIAL” sticker on the outside of the box. Return the box of tips to the proper storage location.
Verify correct caps (color/type) have been brought over to the line by comparing the label on the box of caps to the item number listed on the batch ticket. Initial batch ticket once caps have been verified.
Make sure enough caps have been pulled to the line, so as not to hamper production efficiency.
Keep visual checks on cans for the following, before capping the product: Lot codes present on the dome of cans; Tips have been appropriately placed; No chemical residue or water on top or sides of cans.
Remove any cans with wrinkled or crooked labels to be reworked.
Upon completion of an order, close and tape the box of caps and place a “PARTIAL” sticker on the outside of the box. Return the box of caps to the designated storage location.
Verify that the correct boxes have been brought over to the line by comparing the item numbers printed on the boxes to the item numbers listed on the batch ticket. Initial batch ticket once boxes have been verified.
Ensure boxes are labeled with the appropriate labels before line startup, whether it is a 4x6 white label or PS labels. Apply labels to boxes in a uniform, even manner.
Ensure the lot code has the correct number and is turned on to place the lot codes on all boxes. Ensure the lot code is clear and legible.
Add dividers when required and pack cans into boxes, ensuring all caps remain on cans once placed in the box.
Run the packed box through the tape machine, ensuring the box is sealed correctly.
Pack boxes onto pallet according to established stack patterns.
Upon completion of a pallet, apply the pallet tag with the quantity of cases recorded.
Must pass a pre-employment drug screen.
Must be able to stand and walk for extended periods of time during shift
Must be able to adhere to process protocol

Nice To Haves

High school or equivalent preferred.
Experience working on a production line is desired.
Forklift experience preferred.

Responsibilities

Verify that the correct cans are pulled for the order and maintain a consistent flow of cans to the aerosol lines by loading the can table.
Verify the weight of filled cans after exiting the gassing house and check for leaks as they pass through the water bath.
Responsible for inserting tips (actuators) into aerosol valves during production and assuming other related duties.
Responsible for placing caps onto aerosol cans during production and assuming other duties as necessary, such as labeling and packing.
Responsible for placing filled aerosol cans into boxes and/or stacking onto pallets.
Ensure that all Personal Protective Equipment requirements are met.
As time allows, assist in the final assembly of the product.
Verify with the supervisor as to the end of production
Keep the area clean and organized
Report any problems to the supervisor immediately
Any other duties or projects which the Supervisor may assign