3rd Shift Utility Plant Operator

Fluor Corporation•Rochester, MN

29d•Onsite

About The Position

At Fluor, we are proud to design and build projects and careers. We are committed to fostering a welcoming and collaborative work environment that encourages big-picture thinking, brings out the best in our employees, and helps us develop innovative solutions that contribute to building a better world together. If this sounds like a culture you would like to work in, you're invited to apply for this role. Job Description Follow all health, safely, and environmental requirements ; Perform cleanup duties ; Perform material handling and storage duties ; Identify, use, and care of common hand and power tools ; Use and care of craft specific tools and equipment ; Knowledge and application of craft related mathematics ; Knowledge and use of safety standards and best safety practices relevant to rigging, Inspection of rigging equipment and hardware ; Knowledge and application of common hitches, Emergency stop signal, Basic crane hand signals, Knot tying (bowline & clove hitch), and use of rigging equipment relevant to craft specific tasks ; Understands the various types and function of gears, the components and characteristics of gearbox setups, problems with gears and gear boxes, and gearbox overhaul, including checks and measurements of end play, backlash, tooth contact, and shaft run out ; Understands the operation, components, routine maintenance, and overhaul of centrifugal and reciprocating compressors ; Understands the types and functions, installation, lubrication, maintenance, causes of failure, and replacement of sliding surface and roller contact bearings ; Understands the parts, function, maintenance, and troubleshooting of typical motor operators, including how gears work and the parts, operation, replacement and adjustment of rotary drum limit switches and torque switches ; Understands the types, basic operation, troubleshooting, and overhaul of reciprocating and rotary positive displacement pumps and single and multistage centrifugal pumps ; Understands pipe sizing and materials of construction, pipe storage and handling, characteristics of pipe joints and fittings, and how to measure pipe length, cut, and thread pipe ; Inspects gears and gear units for lubrication problems and bearing failure ; Installs and removes gears ; Checks and adjusts end play, backlash, shaft run out, and tooth contact in gearboxes ; Disassembles, checks, and reassembles centrifugal and reciprocating compressors ; Removes, cleans, inspects, lubricates, and installs various types of bearings ; Disassembles, inspects, and reassembles positive displacement and centrifugal pumps ; Maintains and troubleshoots problems on motor driven valve operators ; Performs complex diagnostics, repairs, calibrations, modifications and routine service on a wide variety of facilities and building equipment, systems, structures and hardware, including air handlers, domestic water, chilled water, hot water, steam, humidification, building exhaust, compressed air, controls, lighting, electrical, security systems, fire systems, etc. ; Completes preventive maintenance (PMs) and client and proactive work orders. ; Implements standard trade practices and procedures (using appropriate safety precautions) for routine maintenance. Produces workmanship commensurate with journeyman level in the following trades: HVAC, electrical, plumbing, welding or electronics. ; Provides technical assistance to junior staff. ; Performs general housekeeping duties in the work areas and shop. ; Complies with all Fluor Corporation safety requirements and programs.

Requirements

Mental Demands: Understand and carry out oral instructions; Read and carry out written instructions to perform work tasks; Work at varying heights; Recognize, avoid, and report safety hazards; Assemble and disassemble objects; Operate equipment and power tools
Physical Demands: See hazards, safety warnings, and barriers; Bend knees for lifting and routine work tasks; Stoop for work positioning and lifting to perform work tasks; Lift maximum 50 lbs without assistance; Ability to comprehend, and respond to audible/visual instructions, alarms and warnings; Climb/balance on ladders, scaffolding, and structures for work tasks; Kneel for work positioning and work task performance; Reach above shoulders and away from body to perform work tasks; Demonstrate manual dexterity to perform work tasks
Working Conditions: Work in extreme heat or cold; Work where noise level is above 85 decibels; Work in wet/humid environment; Work in cramped quarters; Work in environment of fluctuating ventilation; Work inside and outside.

Responsibilities

Follow all health, safely, and environmental requirements
Perform cleanup duties
Perform material handling and storage duties
Identify, use, and care of common hand and power tools
Use and care of craft specific tools and equipment
Knowledge and application of craft related mathematics
Knowledge and use of safety standards and best safety practices relevant to rigging, Inspection of rigging equipment and hardware
Knowledge and application of common hitches, Emergency stop signal, Basic crane hand signals, Knot tying (bowline & clove hitch), and use of rigging equipment relevant to craft specific tasks
Understands the various types and function of gears, the components and characteristics of gearbox setups, problems with gears and gear boxes, and gearbox overhaul, including checks and measurements of end play, backlash, tooth contact, and shaft run out
Understands the operation, components, routine maintenance, and overhaul of centrifugal and reciprocating compressors
Understands the types and functions, installation, lubrication, maintenance, causes of failure, and replacement of sliding surface and roller contact bearings
Understands the parts, function, maintenance, and troubleshooting of typical motor operators, including how gears work and the parts, operation, replacement and adjustment of rotary drum limit switches and torque switches
Understands the types, basic operation, troubleshooting, and overhaul of reciprocating and rotary positive displacement pumps and single and multistage centrifugal pumps
Understands pipe sizing and materials of construction, pipe storage and handling, characteristics of pipe joints and fittings, and how to measure pipe length, cut, and thread pipe
Inspects gears and gear units for lubrication problems and bearing failure
Installs and removes gears
Checks and adjusts end play, backlash, shaft run out, and tooth contact in gearboxes
Disassembles, checks, and reassembles centrifugal and reciprocating compressors
Removes, cleans, inspects, lubricates, and installs various types of bearings
Disassembles, inspects, and reassembles positive displacement and centrifugal pumps
Maintains and troubleshoots problems on motor driven valve operators
Performs complex diagnostics, repairs, calibrations, modifications and routine service on a wide variety of facilities and building equipment, systems, structures and hardware, including air handlers, domestic water, chilled water, hot water, steam, humidification, building exhaust, compressed air, controls, lighting, electrical, security systems, fire systems, etc.
Completes preventive maintenance (PMs) and client and proactive work orders.
Implements standard trade practices and procedures (using appropriate safety precautions) for routine maintenance. Produces workmanship commensurate with journeyman level in the following trades: HVAC, electrical, plumbing, welding or electronics.
Provides technical assistance to junior staff.
Performs general housekeeping duties in the work areas and shop.
Complies with all Fluor Corporation safety requirements and programs.