Structures Technician (Transfer Tube Production) - 2nd Shift

SpaceX•Hawthorne, CA

2d•$23 - $38

About The Position

SpaceX was founded under the belief that a future where humanity is out exploring the stars is fundamentally more exciting than one where we are not. Today SpaceX is actively developing the technologies to make this possible, with the ultimate goal of enabling human life on Mars. STRUCTURES TECHNICIAN (TRANSFER TUBE PRODUCTION) - 2ND SHIFT RESPONSIBILITIES: Modification, repair, assembly, and installation of the rocket and spacecraft Use tooling holes, pilot holes, or by hand (as required), per drawing or tooling instructions Align parts and secure in place using clecos or tooling/hand clamps Check for good edge margins and alignment Shim and/or trim parts as required Select drill bits, reamers and/or countersinking tools for pilot and full size holes Locate, drill pilot holes using drill motor and proper size drill bit(s) Drill, ream, countersink full size holes in parts/assemblies, in proper sequence and to correct size using drill motor Set countersinking tools to proper depth as required Disassemble parts and deburr holes using chip chasers, deburring tools, and files to prepare for installation of fasteners Use solvents to clean surfaces prior to sealing or assembly Apply sealant, alodine, primer, adhesives, special finishes Load and unload ovens to bond detail parts to assemblies Handle and dispose of hazardous materials in approved manner Determine and obtain correct type and size fasteners Cold work holes to prepare for close tolerance fastener installation Install bushings into housings using arbor press and/or hydraulic puller Apply liquid nitrogen to facilitate installation of bushings Install fasteners in correct sequence per drawing, using correct tools (e.g., rivet gun and bucking bar, drill motor, power screwdriver, C-squeeze, ratchet wrench, nut runner) Check work after completion of each operation in job and/or completed job to ensure it is complete per drawing

Requirements

High school diploma or equivalency certificate
1+ years of experience in assembly, manufacturing, military, automotive, or construction OR certificate from an accredited trade school program in A&P, manufacturing, and/or electronics

Nice To Haves

Experience gained through the military or within an aviation manufacturing company
High-volume manufacturing experience
Experience drilling, reaming, honing and/or countersinking straight and close tolerance holes
Experience using various types of hand tools and/or hand-held power tools, floor-mounted power tools and precision measuring tools
Capable of visualizing a three-dimensional shape from a two-dimensional view and understanding symbols, flag notes, and general notes
Ability to perform basic arithmetic calculations accurately (addition, subtraction, multiplication, division, decimals and fractions)
Experience making basic layouts on parts or assemblies in order to establish reference points and to check dimensions
Experience reading and interpreting engineering drawings, blueprints, and specifications
Experience operating computing equipment

Responsibilities

Modification, repair, assembly, and installation of the rocket and spacecraft
Use tooling holes, pilot holes, or by hand (as required), per drawing or tooling instructions
Align parts and secure in place using clecos or tooling/hand clamps
Check for good edge margins and alignment
Shim and/or trim parts as required
Select drill bits, reamers and/or countersinking tools for pilot and full size holes
Locate, drill pilot holes using drill motor and proper size drill bit(s)
Drill, ream, countersink full size holes in parts/assemblies, in proper sequence and to correct size using drill motor
Set countersinking tools to proper depth as required
Disassemble parts and deburr holes using chip chasers, deburring tools, and files to prepare for installation of fasteners
Use solvents to clean surfaces prior to sealing or assembly
Apply sealant, alodine, primer, adhesives, special finishes
Load and unload ovens to bond detail parts to assemblies
Handle and dispose of hazardous materials in approved manner
Determine and obtain correct type and size fasteners
Cold work holes to prepare for close tolerance fastener installation
Install bushings into housings using arbor press and/or hydraulic puller
Apply liquid nitrogen to facilitate installation of bushings
Install fasteners in correct sequence per drawing, using correct tools (e.g., rivet gun and bucking bar, drill motor, power screwdriver, C-squeeze, ratchet wrench, nut runner)
Check work after completion of each operation in job and/or completed job to ensure it is complete per drawing

Benefits

You may also be eligible for long-term incentives, in the form of company stock, stock options, or long-term cash awards, as well as potential discretionary bonuses and the ability to purchase additional stock at a discount through an Employee Stock Purchase Plan.
You will also receive access to comprehensive medical, vision, and dental coverage, access to a 401(k) retirement plan, short and long-term disability insurance, life insurance, paid parental leave, and various other discounts and perks.
You may also accrue 3 weeks of paid vacation and will be eligible for 10 or more paid holidays per year.

Stand Out From the Crowd

Upload your resume and get instant feedback on how well it matches this job.

Upload and Match Resume