Bearing Fabrication - 2nd Shift

Eaton Corporation • Cleveland, OH

22h • $27 • Onsite

About The Position

Eaton’s AER FMC Fuel Motion Control Systems division is currently seeking a Bearing Fabrication - 2nd Shift. he hourly rate for this position is $27.45 per hour. The hours for second shift are as follows; 3:30pm - 12:00am.
Salaries are based upon candidate skills, experience, and qualifications, as well as market and business considerations.
What you’ll do:
Follow print specifications and established operating procedures, perform a variety of operations to fabricate bearing assemblies and apply coatings to a variety of hardware.
Perform visual and dimensional inspections and maintain accurate documentation on a variety of parts in accordance with ANSI Y14-5 and the certified operator program.
Assistance may be given other operators on proper operational procedures.
Perform housekeeping and other job related duties as assigned by supervisor.
Perform preparatory work such as unpacking, visual inspection, degreasing, blasting, masking, plugging, and wrapping, etc., to screen surfaces for spray application according to blueprints, operational sketches, specification sheets, and tool lists.
Perform acid dip of aluminum bearings prior to epoxy operation per operational sketches.
Mix spray compounds according to specifications. Prepare solutions, paying particular attention to volumetric, viscosity and specific gravity requirements.
Clean, adjust and fill spray equipment. Check equipment for proper operation.
On coatings requiring a drying or curing cycle, set oven, or other drying equipment controls to specified temperature and time.
Apply coatings to specified thicknesses.
Use electronic gages (such as Permascope) and other measuring/testing equipment as provided to determine if thickness meets specifications.
Lap and/or ball burnish coated surface to bring into finished tolerances.
Perform all post-operative work such as removing masks, tape and plugs and use solvent to clean up parts as required.
Maintain component build records per government contract requirements.
Handle all materials carefully. Operator must wear fume mask in posted areas.
Perform necessary part marking.
Move material within the cell.
Chart, plot and react to data per SPC requirement.
Load and unload Datamytes.
Maintain accurate lot control (QCP 6.0) traceability, record keeping, log book entries, NCR’s (QCP 11.0) and associated documentation.
Perform minor equipment maintenance.
May be required to perform more than one operation at a time as directed by the supervisor.
May be required to burr work internal to the cycle.
Perform sub-assembly work.

Requirements

• Minimum one (1) year of machining experience OR Minimum one (1) year of industrial painting experience.
• Must have a high school diploma or GED from an accredited institution.
• Eaton will not consider applicants for employment immigration sponsorship or support for this position. This means that Eaton will not support any CPT, OPT, or STEM OPT plans, F-1 to H-1B, H-1B cap registration, O-1, E-3, TN status, I-485 job portability, etc.
• No relocation benefit is offered for this position. Only candidates residing within the immediate area of Euclid, OH (50 miles) will be considered for this position.
• This position requires access to export-controlled information. To conform to U.S. Government export regulations applicable to that information, applicant must be a U.S. person, defined as a (i) U.S. citizen or national, (ii) U.S. lawful, permanent resident (green card holder), (iii) refugee under 8 U.S.C. 1157, or (iv) asylee under 8 U.S.C. 1158.
• Complete an Eaton approved training program within 30 days.
• Become a Certified Operator within 40 days of becoming active on the code.
• Pass an Eaton vision test.

Responsibilities

• Follow print specifications and established operating procedures, perform a variety of operations to fabricate bearing assemblies and apply coatings to a variety of hardware.
• Perform visual and dimensional inspections and maintain accurate documentation on a variety of parts in accordance with ANSI Y14-5 and the certified operator program.
• Assistance may be given other operators on proper operational procedures.
• Perform housekeeping and other job related duties as assigned by supervisor.
• Perform preparatory work such as unpacking, visual inspection, degreasing, blasting, masking, plugging, and wrapping, etc., to screen surfaces for spray application according to blueprints, operational sketches, specification sheets, and tool lists.
• Perform acid dip of aluminum bearings prior to epoxy operation per operational sketches.
• Mix spray compounds according to specifications. Prepare solutions, paying particular attention to volumetric, viscosity and specific gravity requirements.
• Clean, adjust and fill spray equipment. Check equipment for proper operation.
• On coatings requiring a drying or curing cycle, set oven, or other drying equipment controls to specified temperature and time.
• Apply coatings to specified thicknesses.
• Use electronic gages (such as Permascope) and other measuring/testing equipment as provided to determine if thickness meets specifications.
• Lap and/or ball burnish coated surface to bring into finished tolerances.
• Perform all post-operative work such as removing masks, tape and plugs and use solvent to clean up parts as required.
• Maintain component build records per government contract requirements.
• Handle all materials carefully. Operator must wear fume mask in posted areas.
• Perform necessary part marking.
• Move material within the cell.
• Chart, plot and react to data per SPC requirement.
• Load and unload Datamytes.
• Maintain accurate lot control (QCP 6.0) traceability, record keeping, log book entries, NCR’s (QCP 11.0) and associated documentation.
• Perform minor equipment maintenance.
• May be required to perform more than one operation at a time as directed by the supervisor.
• May be required to burr work internal to the cycle.
• Perform sub-assembly work.

Benefits

• Eaton provides various Health and Welfare benefits as well as Retirement benefits, and several programs that provide for paid and unpaid time away from work.

What This Job Offers

• Job Type: Full-time
• Career Level: Entry Level
• Education Level: High school or GED
• Number of Employees: 5,001-10,000 employees