Tool & Die Level II - 2nd Shift

Eaton Corporation • Cleveland, OH

6d • $36 • Onsite

About The Position

The Fuel and Motion Control Systems Division of Eaton’s Aerospace Group has an opening for a Certified Pre-Production. This position is based in Euclid, OH.
Work collaboratively with Engineering to design, modify, or repair tooling, fixtures, and inspection equipment by interpreting engineering prints, specifications, routing sheets, sketches, and verbal instructions; perform associated manufacturing, machining, fitting, assembly, and setup operations.
Perform visual and dimensional inspections and maintain accurate documentation on a variety of parts in accordance with ANSI Y14-5 and the certified operator program.
Assistance may be given to other operators on proper operational procedures.
Plan, develop and manufacture a variety of equipment such as tools, jigs, fixtures, master dies, molds, gauges, inspection equipment, etc., used to manufacture and/or repair components or equipment.
Set up and operate machining and grinding equipment, and perform layout, fitting, assembly, and manufacturing operations including milling, drilling, turning, polishing, etc.
Use existing, or develop new methods, processes, and equipment to plan and execute manufacturing and/or repair operations on equipment and components.
May on occasion be required to develop, set up and operate prototype, sample, or experimental procedures or production lots to test newly developed production methods of tooling.
Use a full range of hand and power tools, as well as a variety of measuring devices equipment to perform job duties and check progress and quality of work, including under black light.
Perform necessary preparatory work which involves layout. Make all necessary set ups which may involve standard or improvised holding devices. Select, install, and dress abrasive wheels most suitable for the phase of work being ground such as contours, radii, angles, etc. Interpret prints of a complex nature and layout sequence of work in most efficient manner possible. Establish proper angular table settings to perform manual forming operations on work requiring the grinding or compound radii and angles.
Occasionally do brazing to affix inserts to tool shanks.
Review tool room supplies, such as tooling, build materials.
Maintain accurate lot control (QCP 6.0) traceability, record keeping, logbook entries, NCR’s (QCP 11.0) and associated documentation.
Perform minor machine maintenance, maintain a clean and organized work area, move materials within the cell, and complete required part marking in accordance with production and safety standards.

Requirements

• Verifiable Skilled Machinist Certification (i.e. Tool & Die Apprentice Program, Journeyman Machinist Program, UAW Apprentice Program, etc.) and have four (4) years’ experience in set up and operation of one or more machine tools (i.e., mills, lathes, drills, grinders) to generate precision parts, including two (2) years full-time CNC machining (resume and/or application must provide detailed work from past employer including this experience).
• Eight (8) years’ full-time experience in the set up and operation of one or more of machine tools (i.e., mills, lathes, drills, grinders) to generate precision parts, including four (4) years full time CNC machining and three (3) years full time precision machining/close tolerance machining (resume and/or application must provide detailed work from past employer including this experience).
• Eaton will not consider applicants for employment immigration sponsorship or support for this position. This means that Eaton will not support any CPT, OPT, or STEM OPT plans, F-1 to H-1B, H-1B cap registration, O-1, E-3, TN status, I-485 job portability, etc.
• No relocation benefit is offered for this position. Only candidates residing within the immediate area of Euclid, OH (50 miles) will be considered for this position.
• This position requires access to export-controlled information. To conform to U.S. Government export regulations applicable to that information, applicant must be a U.S. person, defined as a (i) U.S. citizen or national, (ii) U.S. lawful, permanent resident (green card holder), (iii) refugee under 8 U.S.C. 1157, or (iv) asylee under 8 U.S.C. 1158.
• Pass an Eaton vision test.
• Become a Certified Operator.
• Perform 5S and other duties as assigned.

Responsibilities

• Work collaboratively with Engineering to design, modify, or repair tooling, fixtures, and inspection equipment by interpreting engineering prints, specifications, routing sheets, sketches, and verbal instructions; perform associated manufacturing, machining, fitting, assembly, and setup operations.
• Perform visual and dimensional inspections and maintain accurate documentation on a variety of parts in accordance with ANSI Y14-5 and the certified operator program.
• Assistance may be given to other operators on proper operational procedures.
• Plan, develop and manufacture a variety of equipment such as tools, jigs, fixtures, master dies, molds, gauges, inspection equipment, etc., used to manufacture and/or repair components or equipment.
• Set up and operate machining and grinding equipment, and perform layout, fitting, assembly, and manufacturing operations including milling, drilling, turning, polishing, etc.
• Use existing, or develop new methods, processes, and equipment to plan and execute manufacturing and/or repair operations on equipment and components.
• May on occasion be required to develop, set up and operate prototype, sample, or experimental procedures or production lots to test newly developed production methods of tooling.
• Use a full range of hand and power tools, as well as a variety of measuring devices equipment to perform job duties and check progress and quality of work, including under black light.
• Perform necessary preparatory work which involves layout. Make all necessary set ups which may involve standard or improvised holding devices. Select, install, and dress abrasive wheels most suitable for the phase of work being ground such as contours, radii, angles, etc. Interpret prints of a complex nature and layout sequence of work in most efficient manner possible. Establish proper angular table settings to perform manual forming operations on work requiring the grinding or compound radii and angles.
• Occasionally do brazing to affix inserts to tool shanks.
• Review tool room supplies, such as tooling, build materials.
• Maintain accurate lot control (QCP 6.0) traceability, record keeping, logbook entries, NCR’s (QCP 11.0) and associated documentation.
• Perform minor machine maintenance, maintain a clean and organized work area, move materials within the cell, and complete required part marking in accordance with production and safety standards.

Benefits

• Eaton provides various Health and Welfare benefits as well as Retirement benefits, and several programs that provide for paid and unpaid time away from work.

What This Job Offers

• Job Type: Full-time
• Career Level: Mid Level
• Education Level: No Education Listed
• Number of Employees: 5,001-10,000 employees