OFE Electrician II OR III (Oil Filled Equipment Repair)

Duke Energy Corporation•Charlotte, NC

1d•Onsite

About The Position

Responsible for evaluating, testing, repairing, and maintaining single and three phase Distribution class equipment on a routine basis including but not limited to pole mount transformers, mini-pads, single phase regulators, three phase pad mounts, vaults and reclosers in alignment with the organization set monthly goals. This position is also responsible for: Quality assurance (QA) and warranty repair of single-phase regulators Loading and unloading of tractor trailers of Distribution and Transmission equipment Providing technical guidance and support to Distribution organizations and other departments such as Purchasing, Legal claims, Distribution Field Supervisor, MSR, Distribution Line Tech., Distribution Engineering Standards, Distribution Account Managers, and outside contractors and venders to resolve failures and warranty issues. Special projects such as setting up pad mounts and regulators on 12-kv or 23-kv, dual voltage type transformers, re-configure internal arrestors, bushing wells and putting R-temp oil in units for upcoming major outage for environmental purposes. Within this position, employees must become proficient in evaluating, testing, repairing, and maintaining transformers prior to conducting the same evolution on reclosers.

Requirements

High School/GED degree
Valid Driver's License

Nice To Haves

Technical degree in Electrical study
In addition to desired degree, 2 years related work experience
Forklift certified
Ability to work in a team/group setting, quick learner, safety oriented, detail oriented, strong work ethic, and ability to trouble shoot equipment
Understanding of basic electricity (ac, dc, ohm's law, single phase, three phase, watts, vars, va, power, etc.)
Understanding of Compressed Gas Safety
Understanding of Hazardous Chemicals, MSDS, Facility Emergency Response, and proper handling and disposal of PCB contaminated material and equipment
Understanding of General Machine Guarding/Tool Safety, Includes drills, grinders, power and air actuated tools, and hand tools
Basic understanding of the purpose and proper use of diagnostic test equipment

Responsibilities

Inspection, Evaluation, Testing, and Repair of Distribution Class Equipment
Responsible for evaluating, testing, repairing, and meeting monthly goals on the following types of Distribution equipment
Quality Assurance inspection and testing for single phase regulators
Single phase, one bushing, conventional and CSP transformers, three primary and three secondary voltage classes with capacity ranges from 5kVA to 75kVA, ten different manufactures with various models
Single phase, two bushing, conventional transformers, three primary and six secondary voltage classes with capacity ranges from 25kVA to 500kVA, seven different manufacturers with various models
Single phase pad mount transformers and three phase mini-pad mount transformers, two primary and three secondary voltage classes with capacity ranges from 25kVA to 250kVA, five different manufacturers with various models
Single phase reclosers, five different types, two voltage classes
Three phase reclosers, three different types, two voltage classes
Potential transformers, 0.5 – 1.0kVA rating
Three Phase Pad Mount Transformers
Demonstrate competency in performing work on the equipment listed using the following test equipment
Single and three phase transformer turns ratio (TTR) test sets
Insulation resistance tester (Megger)
Single phase transformer test system (includes TTR, no load loss test, and 400Hz induced voltage test)
Ensure all new equipment meets the appropriate Equipment Specifications and that all work is performed per Distribution Standards guidelines
Be a backup for oil room personnel as needed for the loading and unloading of tankers
Working / assisting in other areas within the shop when needed
Capable of climbing ladders, working off a ladder, or working at heights, off platforms such as tankers that require you to be hooked to harness restraints or fall protection devices
Knowledge of power tools air or electric such as grinders, drills, skill saws, reciprocating saw, impact wrenches, welding, cutting and sand blasting equipment
Ability to perform repetitive tasks while maintaining attention to detail
Ability to read / understand / follow vendor manuals and CAD drawings
Responsible for special projects such as setting up regulators on 12-kv or 23-kv settings or dual type voltage transformers, re-configure internal arrestors, bushing wells and putting R-temp oil in units for upcoming major outage for environmental purposes
Responsible for providing technical guidance support to Distribution personnel such as Distribution Field Supervisor, MSR, Distribution Line Tech, Distribution Engineering Standards , Distribution Account Managers and working with other departments such as Legal, Claims, and Purchasing.
Identifying, troubleshooting, and documenting the root cause or trends with Venders on warranty or non-warranty issues for all Distribution equipment failures and repairs and reporting it to the appropriate organization within Progress Energy so these organizations can make better decision on bench marketing these Manufactures for future purchases or improvements