NDT Inspector- 2nd Shift $33.37

Crane Co.•Elyria, OH

34d•$33 - $33•Onsite

About The Position

Crane Aerospace and Electronics has an exciting opportunity for a Calibration NDT Inspector - 2nd Shift at our Elyria, OH location. Hours are Monday-Friday 3:00pm -11:30pm. About Crane: Crane Aerospace & Electronics supplies critical systems and components to the aerospace and defense markets. You'll find Crane Aerospace & Electronics in some of the toughest environments: from engines to landing gear; from satellites to medical implants and from missiles to unmanned aerial systems (UAS). Our Crane Aerospace & Electronics Elyria facility has been a bedrock in the community-friendly town of Elyria, Ohio, for more than a century. Known for our excellence in pumping technology, our Elyria site produced the first-ever positive displacement pump for high performance piston engine aircraft and even supplied pumps for Charles Lindbergh in the 1930s. We have more than 150,000 fuel and lubrication pumps in service today and are proud to offer custom thermal management system solutions for a range of next-gen applications. Start the next chapter of your career with Crane Aerospace & Electronics! Job Summary: In this role you will ensure all gauges and test equipment used throughout the facility are properly maintained and calibrated to ensure Crane Aerospace products meet specified design standards.

Requirements

High School Diploma
Must be certified to Level II Nondestructive Tester per NAS 410 for Magnetic Particle AND Fluorescent Penetrant Inspection
Prior experience using rotary tables, height stands, electro limit/shadow gauges, comparator, sine bar, profilometer and micrometers
Must have successfully completed NDT/Calibration Inspector trainee occupation (internal applicants only)
Must have basic reading and writing skills
Requires basic math skills to make necessary calculations such as adding, subtracting, multiplying, and dividing
Must have sufficient knowledge of geometry and trigonometry.
Must be able to read and interpret blueprints, detail sheets, manufacturing outlines, and written instructions
Must be able to apply detailed techniques to products or parts
Proficient working computer knowledge
Eligibility Requirement: This position may require access to Controlled Data or Information. Where the position requires such access only US Persons will be considered. As a US Department of Defense contractor, we are bound by International Traffic in Arms Regulations (ITAR).
NDT Level II certifications in Magnetic Particle AND Fluorescent Penetrant Inspection per NAS 410
Requires prolonged periods of sitting, standing, bending, lifting, and stretching;
Requires occasional lifting parts up to 50 pounds;
Requires frequent lifting and handling parts weighing up to 30 pounds.

Nice To Haves

Prior calibration experience preferred

Responsibilities

Perform Process Control Checks per NAS standard.
Process parts per internal operating procedures.
Responsible for maintaining an adequate level of inventory needed for the department.
Maintain Level II NDT certifications in Magnetic Particle and Fluorescent Penetrant Inspection per NAS 410.
Responsible for issuance, control, and calibration of all measuring equipment.
Calibrate all measuring equipment used for the manufacture, acceptance, and test of product and components manufactured or purchased by Crane Co.
Maintain calibration computer database with all necessary information.
Handle and store all measuring equipment to eliminate potential damage.
Assign and mark measuring equipment with necessary identification information to enable equipment to be monitored by the department supervisors and the calibration system.
Monitor the daily calibration reports and contact department supervisors when delinquent gauges are not returned.
Work closely with Inspection and Production Test Supervision for repair, replacement and subcontracted calibration of measuring equipment is required,
Clean and move parts as necessary.
Pass an annual eye exam per NAS 410.
Perform routine maintenance per Appendix A and appropriate safety checks.
Responsible for product verification and process control including using necessary measuring devices.
Keep charts and records as required on completed sequences and processes.
Document all non-conformances through specified data collection procedures.
Complete all required paperwork.
Ensure all material is properly cleaned, identified, protected, and stacked prior to movement.
Work with internal and external customers and suppliers and participate in continuous improvement activities as required.
Complete all required documentation including but not limited to operator inspection records, job routers, NCR's, reject tags, move tickets, and stock tickets.
Perform other duties as assigned by department supervisor.
Utilize computer to access various databases.

Benefits

Health care, dental, vision, life and disability insurance start after completing 90 days of employment.
Education Reimbursement: eligible after 6 months of employment

Stand Out From the Crowd

Upload your resume and get instant feedback on how well it matches this job.

Upload and Match Resume