Manufacturing Technician I- 2nd Shift (Structure Line)

Eaton Corporation • Fayetteville, NC

37d • $16 • Onsite

About The Position

The Manufacturing Technician I - 2nd Shift (Structure Line), will assemble, fit and mount sub-assemblies, components, and standard and near standard fixed assemblies in Motor Control Centers, Enclosed Control and related assemblies and sub-assemblies. Perform assembly required for test preparation and final inspection. Assemble and wire units, relay panels, panel boards, space heaters, and control panels. Bend and install power cable and leads, fabricate pre-cable unit, panel and MTB harnesses, and power leads. Use established power checking procedures and equipment to verify electrical/mechanical integrity of units assembled. Stage parts for customer orders. In this function you will: A. Work from oral or written instructions from supervision and/or prints, inspection reports, manufacturing information sheets, and standard or near standard wiring diagrams. B. Utilize manufacturing information sheets, determine necessary parts, write requisitions, and obtain materials from stock areas. C. Read shop orders and drawings to determine assembly procedures such as component types and configuration, mounting locations and clearances required. D. Assemble and fit parts and components to form sub-assemblies, or completed assemblies. E. Assemble and wire control devices, cutting wires to length. F. Make adjustments to insure correct alignment and clearances. G. Install units, pan assemblies and cover up steel, meters, kirk keys, pull boxes, reactors, relays, fuses, MTB assemblies, panel boards, space heaters, transformers, etc. by mounting / bolting into place. Assemble and install bus work such as lug adapters, cross over bus, splices, etc. H. Make pre-bent cable unit, MTB and control panel harnesses using pre-cable boards, control panels and hand crimp lugs if necessary. Cut, install and connect wire and/or cable in units where circuitry requires additional relays, timers, fuses, etc. Cut, form and connect control wire, power wire and cable, point to point on units, relay panels, control panels, and space heaters. Make solder connections. I. Modify standard assemblies or doors as received. May alter hole cutouts, etc. using hand or power tools.

Requirements

• High school diploma or GED from an accredited institution
• Must reside within a 50-mile radius of Fayetteville, NC (Active Duty military are exempt from the geographical requirement)
• Eaton will not consider applicants for employment immigration sponsorship or support for this position. This means that Eaton will not support any CPT, OPT, or STEM OPT plans, F-1 to H-1B, H-1B cap registration, O-1, E-3, TN status, I-485 job portability, etc.

Nice To Haves

• Manufacturing or production experience preferred.

Responsibilities

• Assemble, fit and mount sub-assemblies, components, and standard and near standard fixed assemblies in Motor Control Centers, Enclosed Control and related assemblies and sub-assemblies.
• Perform assembly required for test preparation and final inspection.
• Assemble and wire units, relay panels, panel boards, space heaters, and control panels.
• Bend and install power cable and leads, fabricate pre-cable unit, panel and MTB harnesses, and power leads.
• Use established power checking procedures and equipment to verify electrical/mechanical integrity of units assembled.
• Stage parts for customer orders.
• Work from oral or written instructions from supervision and/or prints, inspection reports, manufacturing information sheets, and standard or near standard wiring diagrams.
• Utilize manufacturing information sheets, determine necessary parts, write requisitions, and obtain materials from stock areas.
• Read shop orders and drawings to determine assembly procedures such as component types and configuration, mounting locations and clearances required.
• Assemble and fit parts and components to form sub-assemblies, or completed assemblies.
• Assemble and wire control devices, cutting wires to length.
• Make adjustments to insure correct alignment and clearances.
• Install units, pan assemblies and cover up steel, meters, kirk keys, pull boxes, reactors, relays, fuses, MTB assemblies, panel boards, space heaters, transformers, etc. by mounting / bolting into place. Assemble and install bus work such as lug adapters, cross over bus, splices, etc.
• Make pre-bent cable unit, MTB and control panel harnesses using pre-cable boards, control panels and hand crimp lugs if necessary. Cut, install and connect wire and/or cable in units where circuitry requires additional relays, timers, fuses, etc. Cut, form and connect control wire, power wire and cable, point to point on units, relay panels, control panels, and space heaters. Make solder connections.
• Modify standard assemblies or doors as received. May alter hole cutouts, etc. using hand or power tools.

Benefits

• Eaton provides various Health and Welfare benefits as well as Retirement benefits, and several programs that provide for paid and unpaid time away from work. Click here for more detail: Eaton Benefits Overview.

What This Job Offers

• Job Type: Full-time
• Career Level: Entry Level
• Industry: Professional, Scientific, and Technical Services
• Education Level: High school or GED
• Number of Employees: 5,001-10,000 employees