Manufacturing Technician-I MCC Assembly

Eaton Corporation•Fayetteville, NC

5d•Onsite

About The Position

The Manufacturing Technician - I MCC Assembly, will assemble, fit and mount sub-assemblies, components, and standard and near standard fixed assemblies in Motor Control Centers, Enclosed Control and related assemblies and sub-assemblies. Perform assembly required for test preparation and final inspection. Assemble and wire units, relay panels, panel boards, space heaters, and control panels. Bend and install power cable and leads, fabricate pre-cable unit, panel and MTB harnesses, and power leads. Use established power checking procedures and equipment to verify electrical/mechanical integrity of units assembled. Stage parts for customer orders. In this function you will: A. Work from oral or written instructions from supervision and/or prints, inspection reports, manufacturing information sheets, and standard or near standard wiring diagrams. B. Utilize mfg. information sheets, determine necessary parts, write requisitions, & obtain materials from stock areas. C. Read shop orders and drawings to determine assembly procedures such as component types and configuration, mounting locations and clearances required. D. Assemble and fit parts and components to form sub-assemblies, or completed assemblies. E. Assemble and wire control devices, cutting wires to length. F. Make adjustments to insure correct alignment and clearances. G. Install units, pan assemblies and cover up steel, meters, kirk keys, pull boxes, reactors, relays, fuses, MTB assemblies, panel boards, space heaters, transformers, etc. by mounting / bolting into place. Assemble and install bus work such as lug adapters, cross over bus, splices, etc. H. Make pre-bent cable unit, MTB and control panel harnesses using pre-cable boards, control panels and hand crimp lugs if necessary. I. Modify standard assemblies or doors as received. May alter hole cutouts, etc. using hand or power tools. J. Make wiring changes as required. K. Use floor operated overhead and jib cranes. Move units, harnesses, device panels, etc. from one area to another. L. Determine the quality of work reporting problems to area supervisor or Quality Control personnel. Maintain piece count and associated records where applicable. M. Mark wires, devices or terminals as required. Identify harness and/or panels with job and unit number. Apply component ID labels such as “Brady Markers” or “Dymo” labels if required. Identify work and maintain records. N. Wear all safety equipment and observe all hygiene requirements as specified and directed. through the assembly / manufacturing process.

Requirements

High school diploma or GED from an accredited institution is required
Minimum of 3 months previous experience in manufacturing environment
Work with individuals and groups to effectively participate within team environment
Willing to work flexible hours and overtime in support of business needs
Demonstrated comprehension of wiring diagrams and schematics
Utilize various hand tools to assembly and wire products in a lean environment
Self-driven and able to produce desired results with minimal direction
Able to stand; walk; sit; reach at or above shoulder level; grip; and use hands to handle and feel
Able to frequently lift/carry up to 35 pounds
Able to push/pull up to 35 pounds
Adequate far and close vision with depth perception and color discrimination
Maintain a clean work area
Keep health and safety equipment in good working order

Responsibilities

Assemble, fit and mount sub-assemblies, components, and standard and near standard fixed assemblies
Perform assembly required for test preparation and final inspection
Assemble and wire units, relay panels, panel boards, space heaters, and control panels
Bend and install power cable and leads, fabricate pre-cable unit, panel and MTB harnesses, and power leads
Use established power checking procedures and equipment to verify electrical/mechanical integrity of units assembled
Stage parts for customer orders
Work from oral or written instructions from supervision and/or prints, inspection reports, manufacturing information sheets, and standard or near standard wiring diagrams
Utilize mfg. information sheets, determine necessary parts, write requisitions, & obtain materials from stock areas
Read shop orders and drawings to determine assembly procedures such as component types and configuration, mounting locations and clearances required
Assemble and fit parts and components to form sub-assemblies, or completed assemblies
Assemble and wire control devices, cutting wires to length
Make adjustments to insure correct alignment and clearances
Install units, pan assemblies and cover up steel, meters, kirk keys, pull boxes, reactors, relays, fuses, MTB assemblies, panel boards, space heaters, transformers, etc. by mounting / bolting into place
Assemble and install bus work such as lug adapters, cross over bus, splices, etc
Make pre-bent cable unit, MTB and control panel harnesses using pre-cable boards, control panels and hand crimp lugs if necessary
Modify standard assemblies or doors as received. May alter hole cutouts, etc. using hand or power tools
Make wiring changes as required
Use floor operated overhead and jib cranes. Move units, harnesses, device panels, etc. from one area to another
Determine the quality of work reporting problems to area supervisor or Quality Control personnel
Maintain piece count and associated records where applicable
Mark wires, devices or terminals as required
Identify harness and/or panels with job and unit number
Apply component ID labels such as “Brady Markers” or “Dymo” labels if required
Identify work and maintain records
Wear all safety equipment and observe all hygiene requirements as specified and directed through the assembly / manufacturing process