Manufacturing Operator II-PTFE Extrusion

Eaton Corporation•Middlesex, NC

3d•Onsite

About The Position

Experienced level of machine operator requiring the ability to follow written instructions and read blueprint specifications. Under moderate supervision, sets up and operates alternately more than one type of production machine on a limited range of production work, involving close tolerances and set-ups, which are exacting, but not usually highly involved or difficult. Adjusts machine components to regulate speeds, pressures, feeds and operation sequence are ordinarily prescribed. The operator will be required to learn and work in multiple areas below Powder Blending & Perform 4” Tube Extrusion 6” Tube Extrusion 7” Tube Extrusion ILS Tube Extrusion The operator might be required to cross train in areas below Thermoplastic Tube Extrusion Thermoplastic Cover Extrusion Silicone Extrusion Pull powder from staging area and load powder into perform press Set up extruder with proper pin and die according to set-up sheet Load billet into extruder Set limit switch and set dial speed for extruder Examine extruded tube at beginning and end of each billet Extrude tube onto pan(batch)/reel Chart measures Move pan to oven and load (batch) (MUST CERTIFY ON LIFT TRUCK) Apply mica dust to tube Remove mica dust from pan Monitor tube dimensions Set timers and start ovens (batch) Perform operations in MFGPro Disburse raw materials Keep up air emissions log Perform duties relative to production in the assigned area and is able to operate all equipment and machinery in the assigned area, including lift truck. Produce a quality product, safely, on-time, and with the least cost possible. Review work orders, specifications or instructions to determine material, ingredients, procedures, components and settings. Accurately record data on process travelers. Accurately complete computer transactions as necessary (labor & scrap transactions, inventory disbursements & cycle counts, expense items, etc.). Participate in cell/team activities including, but not limited to, team meetings, problem-solving, Kaizen events, etc. Maintain a safe, clean and orderly work environment through effective housekeeping, 5S and TPM practices Follow all plant, safety, and environmental rules and regulations. Support plant lean, safety, quality and continuous improvement efforts. Perform all other duties as required. Know and follow established job specific and facility wide health and safety procedures. Bring health and safety issues, unsafe acts and safety suggestions to management's attention and correct those they can. Assist in developing job safety analysis and safe working procedures. Identify and correct hazards and unsafe conditions. Accident, near-miss accident or potential hazard investigations. Actively participate in health and safety training and demonstrate competency based on training received. Participate actively in providing suggestions for the health and safety program improvement. Know and implement regulatory compliance requirements in designated work area.

Requirements

High School Diploma
6 months of Manufacturing experience
Must live within 50 miles
This position requires use of information or access to hardware which is subject to the International Traffic in Arms Regulations (ITAR). All applicants must be U.S. persons within the meaning of ITAR. ITAR defines a U.S. person as a U.S. Citizen, U.S. Permanent Resident (i.e. 'Green Card Holder'), Political Asylee, or Refugee.
Good verbal and written communication skills
Good problem-solving, prioritization and decision-making skills
Good interpersonal skills/teaming ability
Ability to learn computer transactions
Ability to learn and successfully operate production equipment

Responsibilities

Pull powder from staging area and load powder into perform press
Set up extruder with proper pin and die according to set-up sheet
Load billet into extruder
Set limit switch and set dial speed for extruder
Examine extruded tube at beginning and end of each billet
Extrude tube onto pan(batch)/reel
Chart measures
Move pan to oven and load (batch) (MUST CERTIFY ON LIFT TRUCK)
Apply mica dust to tube
Remove mica dust from pan
Monitor tube dimensions
Set timers and start ovens (batch)
Perform operations in MFGPro
Disburse raw materials
Keep up air emissions log
Perform duties relative to production in the assigned area and is able to operate all equipment and machinery in the assigned area, including lift truck
Produce a quality product, safely, on-time, and with the least cost possible
Review work orders, specifications or instructions to determine material, ingredients, procedures, components and settings
Accurately record data on process travelers
Accurately complete computer transactions as necessary (labor & scrap transactions, inventory disbursements & cycle counts, expense items, etc.)
Participate in cell/team activities including, but not limited to, team meetings, problem-solving, Kaizen events, etc.
Maintain a safe, clean and orderly work environment through effective housekeeping, 5S and TPM practices
Follow all plant, safety, and environmental rules and regulations
Support plant lean, safety, quality and continuous improvement efforts
Perform all other duties as required
Know and follow established job specific and facility wide health and safety procedures
Bring health and safety issues, unsafe acts and safety suggestions to management's attention and correct those they can
Assist in developing job safety analysis and safe working procedures
Identify and correct hazards and unsafe conditions
Accident, near-miss accident or potential hazard investigations
Actively participate in health and safety training and demonstrate competency based on training received
Participate actively in providing suggestions for the health and safety program improvement
Know and implement regulatory compliance requirements in designated work area