Facility Maintenance Electrician III

Amentum

12d•$30 - $35•Onsite

About The Position

Amentum is seeking a 1st shift Industrial Electrician III in Mossville Tech Center. Typical work hours are 6:00 AM -4:30 PM M-Th or T-F; hours may vary based on business demand. This electrical maintenance technician is responsible for providing an intermediate level of expertise in responding to work orders, troubleshooting, and providing preventive maintenance on the facility electrical equipment in an industrial, large commercial, or logistics distribution environment. This maintenance electrician is responsible for providing an intermediate level of expertise in responding to work orders, troubleshooting, and providing preventive and corrective maintenance on the facility electrical and mechanical equipment. Must have the ability to install conduit and terminate wiring, diagnose and troubleshoot all electrical equipment and systems including, but not limited to, motors, drives, low voltage controls, lighting, PLC’s, HVAC, Chiller, etc. Must demonstrate good written and verbal communication. The Industrial Electrician III must have the ability to identify and correct any safety-related issues and perform independent equipment evaluations to identify potential equipment failures. General Maintenance of equipment will also be required. Responsibilities: Diagnoses, troubleshoots, maintains, and repairs electrical equipment up to 480-volt 3 phase and facility systems such as RTU, doors, lighting, VFDs and motors circuits. Runs conduit and terminates wire according to job specified Working knowledge of the National Electric Code (NEC) Utilizes the building automation system to track building conditions and the operation of facilities equipment. Utilizes strong electrical and mechanical skills to complete assignments. Performs preventive maintenance on industrial electrical control and operating systems as scheduled in the Computerized Maintenance Management System (CMMS). Responds and provides service and feedback to the customer on all work orders while assuring compliance to codes, regulations and industry standards. Recommends measures to improve maintenance methods and equipment performance. Understands company policies and enforces safety regulations. Safely performs functions of the position including following proper safety guidelines such as job hazard analysis and lockout/tagout procedures and wearing PPE as required. Maintain, troubleshoot and repair electrical equipment, such as area personal fans, thermostats for gas and electric heaters, reset of buss bars and disconnects, etc Troubleshooting of electrical components such as, but not limited to PLC’s, AC & DC drives, relay logic, single loop controllers, pneumatics & hydraulics Operates various measuring, diagnostic and electrical testing instruments to help provide energy efficiency solutions. Electrical system components - MCC’s, inverters, motors, etc. Ability to read and interpret mechanical and electrical schematics/prints, updating electrical prints/schematics assigned for modification Operates a variety of equipment such as hand tools, laptop computers and diagnostic hardware to perform work. Maintains a strict schedule in order to be successful in the assignment yet demonstrates flexibility in the day-to-day activities and scheduling for the benefit of the customer. Math skills to include Arithmetic, Application of formulas such as current, voltage, etc., Conversion of measurement units Other duties as assigned by Manager or Supervisor.

Requirements

High school diploma or demonstrated equivalent.
Three years of experience as a maintenance electrician in an industrial environment or demonstrated equivalent combination of education and experience.
Must have the ability to work in an aerial lift or scissor lift at heights up to 30 feet or higher.

Nice To Haves

Experience working safely with 480V 3 phase circuits.
Experience troubleshooting and repairing industrial lighting systems.
Experience making repairs on rubber production or similar equipment.
Experience troubleshooting and repairing electric motors and motor controls.
Experience troubleshooting VFD’s.
Experience working with a PC-based work order opening, closing and time reporting system.

Responsibilities

Diagnoses, troubleshoots, maintains, and repairs electrical equipment up to 480-volt 3 phase and facility systems such as RTU, doors, lighting, VFDs and motors circuits.
Runs conduit and terminates wire according to job specified
Working knowledge of the National Electric Code (NEC)
Utilizes the building automation system to track building conditions and the operation of facilities equipment.
Utilizes strong electrical and mechanical skills to complete assignments.
Performs preventive maintenance on industrial electrical control and operating systems as scheduled in the Computerized Maintenance Management System (CMMS).
Responds and provides service and feedback to the customer on all work orders while assuring compliance to codes, regulations and industry standards.
Recommends measures to improve maintenance methods and equipment performance.
Understands company policies and enforces safety regulations.
Safely performs functions of the position including following proper safety guidelines such as job hazard analysis and lockout/tagout procedures and wearing PPE as required.
Maintain, troubleshoot and repair electrical equipment, such as area personal fans, thermostats for gas and electric heaters, reset of buss bars and disconnects, etc
Troubleshooting of electrical components such as, but not limited to PLC’s, AC & DC drives, relay logic, single loop controllers, pneumatics & hydraulics
Operates various measuring, diagnostic and electrical testing instruments to help provide energy efficiency solutions.
Electrical system components - MCC’s, inverters, motors, etc.
Ability to read and interpret mechanical and electrical schematics/prints, updating electrical prints/schematics assigned for modification
Operates a variety of equipment such as hand tools, laptop computers and diagnostic hardware to perform work.
Maintains a strict schedule in order to be successful in the assignment yet demonstrates flexibility in the day-to-day activities and scheduling for the benefit of the customer.
Math skills to include Arithmetic, Application of formulas such as current, voltage, etc., Conversion of measurement units
Other duties as assigned by Manager or Supervisor.