Electronics Tester

Eaton Corporation • Glenolden, PA

1d • $27 • Onsite

About The Position

Eaton’s IS AER FED division is currently seeking a Electronics Tester to join our team in Glenolden, PA!
The is a 1st shift position and the core hours are 7 am - 3 pm, M-F.
The hourly rate for this position is $26.50 per hour.
Please note the salary information shown above is a general guideline only. Salaries are based upon candidate skills, experience, and qualifications, as well as market and business considerations.
What you’ll do:
The Electronics Tester is responsible for testing electro-mechanical products for compliance to Acceptance Test Procedures (ATPs) and customer/internal drawings.
In this role, you will:
• Verify product compliance to Acceptance Test Procedures (ATP) / drawings and maintain accurate ATP records
• Utilize test fixtures and test equipment including oscilloscopes, function generator, device programmer, mass spectrometer, vibration table, tenney chamber, hot oil room, etc. to perform ATP.
• Troubleshoot and diagnose common failure modes when test failures occur.
• Inspect and diagnose PC Boards to component level (for failure analysis)
• Works from work orders, engineering drawings, and visual/written work instructions to assemble electro- mechanical components.
• Coordinate with Engineering group for shared resources and test validation
• Identify and initiate continuous improvement for product safety, quality, and efficiency.

Requirements

• High School Diploma or GED equivalent from accredited institution
• Minimum of 2 years of experience in electro-mechanical environment
• Eaton will not consider applicants for employment immigration sponsorship or support for this position. This means that Eaton will not support any CPT, OPT, or STEM OPT plans, F-1 to H-1B, H-1B cap registration, O-1, E-3, TN status, I-485 job portability, etc.
• No relocation benefit is being offered for this position. Only candidates within a 50-mile radius of the work location will be considered. Active-Duty Military Service member candidates are exempt from the geographical area limitation.
• This position requires use of information or access to hardware which is subject to the International Traffic in Arms Regulations (ITAR). All applicants must be U.S. persons within the meaning of ITAR. ITAR defines a U.S. person as a U.S. Citizen, U.S. Permanent Resident (i.e. 'Green Card Holder'), Political Asylee, or Refugee
• Basic understanding of pressure theory, electronic theory, and, Ohm’s law and the relationship between resistance, current, and voltage.
• When an assembly fails resistance at in process or final test the employee should be capable of diagnosing and recommending fixing, where applicable, in most cases.
• Capable of measuring resistor components with multimeter
• Ability to perform ATP product testing using Labview programming interface and test racks.
• Knowledge of High and Low pressure test vessels and safety precautions when working
• Proper use of Mil-Spec oils and gasses
• Basic Electronics and Mechanical Theory in relation to PC Board troubleshooting
• Position requires use of PPE – Safety glasses, safety shoes, gloves as needed

Nice To Haves

• Associates or Technical degree in Electronics or related field from an accredited institution.
• Minimum of 2 years ofelectronic testing experience in a manufacturing environment.

Responsibilities

• Verify product compliance to Acceptance Test Procedures (ATP) / drawings and maintain accurate ATP records
• Utilize test fixtures and test equipment including oscilloscopes, function generator, device programmer, mass spectrometer, vibration table, tenney chamber, hot oil room, etc. to perform ATP.
• Troubleshoot and diagnose common failure modes when test failures occur.
• Inspect and diagnose PC Boards to component level (for failure analysis)
• Works from work orders, engineering drawings, and visual/written work instructions to assemble electro- mechanical components.
• Coordinate with Engineering group for shared resources and test validation
• Identify and initiate continuous improvement for product safety, quality, and efficiency.

Benefits

• Eaton provides various Health and Welfare benefits as well as Retirement benefits, and several programs that provide for paid and unpaid time away from work. Click here for more detail: Eaton Benefits Overview.

What This Job Offers

• Job Type: Full-time
• Career Level: Entry Level
• Education Level: High school or GED
• Number of Employees: 5,001-10,000 employees