Certified Gear & Shaft Utility - LEVEL II - 2nd Shift

Eaton Corporation • Cleveland, OH

26d • $27 • Onsite

About The Position

Eaton’s AER FMC Fuel Motion Control Systems division is currently seeking a Certified Gear & Shaft Utility - LEVEL II - 2nd Shift. The core hours are 3:30pm to 12:00am. The hourly rate for this position is 27.45 per hour.
Please note the salary information shown above is a general guideline only. Salaries are based upon candidate skills, experience, and qualifications, as well as market and business considerations.
The Fuel and Motion Control Systems Division of Eaton’s Aerospace Group has an opening for a Certified Gear and Shaft Utility. This position is based in Euclid, OH. The Euclid facility has approximately 300 employees and is a leader in the design, development, manufacture and delivery of Aerospace Fuel Pumping components, systems and services to the global aftermarket and OEM markets.
Set up and operate various burring, cleaning, buffing and blasting machines to generate rough and finish dimensions on a variety of parts. Perform operations such as nitride, heat treat, buff and blast. Also perform hand operations required to burr, polish, finish, and blend surfaces on machined parts.
Perform visual and dimensional inspections and maintain accurate documentation on a variety of parts in accordance with ANSI Y14-5 and the Certified Operator program.
Assistance may be given to other operators on proper operational procedures.
Load, unload and monitor processing of parts in heat treat basket, load furnaces, operate furnaces, monitor gages, unload furnaces, and perform hardness test.
Perform various burr, buff, dry blast, degrease and oiling operations on hardware.
Set up, operate, monitor, read, interpret, and maintain furnace, atmosphere generation, and quench equipment controls and instruments such as timers, temperature control and monitoring recorder charts, flow scopes, pressure gages, various dial gages. Instruments may be analog or digital (programmable microprocessor) based.
Set up and operate all equipment with a minimum of assistance, be familiar with work procedures involved with nitride, heat treating, and buffing operations. Frequent changes in set-up and maintenance of close tolerance require constant attention.
Mount and accurately align various jig and fixtures, select speeds, and feeds. Load and align tooling working from engineering layouts. Adjust stops and cams to produce finish dimensions to tolerances.
Read and interpret moderately complicated blueprints and execute quality checks using a variety of mechanical and electronic gages.
Maintain accurate lot control (QCP 6.0) traceability, record keeping, log book entries, NCR’s (QCP 11.0) and associated documentation.
Generate close tolerance edge breaks using various hand tools.

Requirements

• High School Diploma or GED from an accredited institution.
• Minimum one (1) year of machining/utility, heat treat or nitride experience.
• Minimum 1-year GD&T Experience (successful completion of Eaton Level 1 Advanced Training will be considered in lieu of this requirement).
• Eaton will not consider applicants for employment immigration sponsorship or support for this position. This means that Eaton will not support any CPT, OPT, or STEM OPT plans, F-1 to H-1B, H-1B cap registration, O-1, E-3, TN status, I-485 job portability, etc.
• No relocation benefit is offered for this position. Only candidates residing within the immediate area of Euclid, OH (50 miles) will be considered for this position.

Responsibilities

• Set up and operate various burring, cleaning, buffing and blasting machines to generate rough and finish dimensions on a variety of parts.
• Perform operations such as nitride, heat treat, buff and blast.
• Perform hand operations required to burr, polish, finish, and blend surfaces on machined parts.
• Perform visual and dimensional inspections and maintain accurate documentation on a variety of parts in accordance with ANSI Y14-5 and the Certified Operator program.
• Assistance may be given to other operators on proper operational procedures.
• Load, unload and monitor processing of parts in heat treat basket, load furnaces, operate furnaces, monitor gages, unload furnaces, and perform hardness test.
• Perform various burr, buff, dry blast, degrease and oiling operations on hardware.
• Set up, operate, monitor, read, interpret, and maintain furnace, atmosphere generation, and quench equipment controls and instruments such as timers, temperature control and monitoring recorder charts, flow scopes, pressure gages, various dial gages.
• Set up and operate all equipment with a minimum of assistance, be familiar with work procedures involved with nitride, heat treating, and buffing operations.
• Mount and accurately align various jig and fixtures, select speeds, and feeds.
• Load and align tooling working from engineering layouts.
• Adjust stops and cams to produce finish dimensions to tolerances.
• Read and interpret moderately complicated blueprints and execute quality checks using a variety of mechanical and electronic gages.
• Maintain accurate lot control (QCP 6.0) traceability, record keeping, log book entries, NCR’s (QCP 11.0) and associated documentation.
• Generate close tolerance edge breaks using various hand tools.

Benefits

• Eaton provides various Health and Welfare benefits as well as Retirement benefits, and several programs that provide for paid and unpaid time away from work.

What This Job Offers

• Job Type: Full-time
• Career Level: Entry Level
• Education Level: High school or GED
• Number of Employees: 5,001-10,000 employees