Assembly and Test Technician

Eaton Corporation • Jackson, MS

1d • $22 • Onsite

About The Position

Eaton’s IS AER FMC division is currently seeking a Assembly and Test Technician. The hourly rate for this position is $22.40 + $1.00 shift differential per hour. The hours for this shift are 3:30 pm - 12:00 am. Salaries are based upon candidate skills, experience, and qualifications, as well as market and business considerations. What you’ll do: JOB DESCRIPTION KEY ACCOUNTABILITIES: Assembles and builds all non-Marine & Defense sub-assemblies, rotating group, pumps, and motors having close tolerances and critical operating requirements where fitting, alignment, and adjustment are precise. Completes all required quality and customer information on reports and documents. Must be able to troubleshoot and repair to full operational status, all REO and failed test stand pumps and motors. Sets up and/or operates all assembly department test stands without assistance and maintains appropriate requirements. In cases where automated test stands are present, operator may be responsible for the operation of two stands. Reads and interprets test procedures to determine if the unit meets all applicable quality and standards requirements. Read gauges as required by the test procedures and transfers applicable/required data to defined quality reports and documents. Interpret hydraulic schematics, pressure gauges, strip recorders and test stand "х-y" plots. Must be able to read and interpret assembly and component prints and component maintenance manuals as may be required. Responsible for the cleaning and packing operations required for the rotating group processing. Utilizes hand tools in building and testing units. Employs measurement instrumentation such micrometers, venire calipers, etc. to check/verify dimensional assembly requirements as needed. Responsible for maintaining cleanliness and order in all working areas maintaining that area to the highest degree of cleanliness required for assembly operations. Qualifications: BASIC QUALIFICATIONS: High school diploma or GED required Minimum two (2) years of experience performing complete mechanical assembly, disassembly, and troubleshooting in a manufacturing, military, or aviation environment -OR- Associate degree in Precision Manufacturing and Machining Technology This position requires use of information or access to hardware which is subject to the International Traffic in Arms Regulations (ITAR). All applicants must be U.S. persons within the meaning of ITAR. ITAR defines a U.S. person as a U.S. Citizen, U.S. Permanent Resident (i.e. 'Green Card Holder'), Political Asylee, or Refugee. No relocation benefits are being offered for this position. Only candidates residing within 50 miles of Eaton's Jackson, MS facility will be considered for this position.

Requirements

• High school diploma or GED required
• Minimum two (2) years of experience performing complete mechanical assembly, disassembly, and troubleshooting in a manufacturing, military, or aviation environment
• Associate degree in Precision Manufacturing and Machining Technology
• All applicants must be U.S. persons within the meaning of ITAR. ITAR defines a U.S. person as a U.S. Citizen, U.S. Permanent Resident (i.e. 'Green Card Holder'), Political Asylee, or Refugee.
• Only candidates residing within 50 miles of Eaton's Jackson, MS facility will be considered for this position.

Responsibilities

• Assembles and builds all non-Marine & Defense sub-assemblies, rotating group, pumps, and motors having close tolerances and critical operating requirements where fitting, alignment, and adjustment are precise.
• Completes all required quality and customer information on reports and documents.
• Must be able to troubleshoot and repair to full operational status, all REO and failed test stand pumps and motors.
• Sets up and/or operates all assembly department test stands without assistance and maintains appropriate requirements. In cases where automated test stands are present, operator may be responsible for the operation of two stands.
• Reads and interprets test procedures to determine if the unit meets all applicable quality and standards requirements. Read gauges as required by the test procedures and transfers applicable/required data to defined quality reports and documents.
• Interpret hydraulic schematics, pressure gauges, strip recorders and test stand "х-y" plots. Must be able to read and interpret assembly and component prints and component maintenance manuals as may be required.
• Responsible for the cleaning and packing operations required for the rotating group processing.
• Utilizes hand tools in building and testing units. Employs measurement instrumentation such micrometers, venire calipers, etc. to check/verify dimensional assembly requirements as needed.
• Responsible for maintaining cleanliness and order in all working areas maintaining that area to the highest degree of cleanliness required for assembly operations.

Benefits

• Eaton provides various Health and Welfare benefits as well as Retirement benefits, and several programs that provide for paid and unpaid time away from work.

What This Job Offers

• Job Type: Full-time
• Career Level: Entry Level
• Education Level: High school or GED
• Number of Employees: 5,001-10,000 employees